Plumbing Essentials: An Essential for Installing a Bathtub
Plumbing Essentials: An Essential for Installing a Bathtub
Blog Article
What're your concepts about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't precisely brain surgery, but it does require strong plumbing, woodworking, and also in some cases, tiling skills. Replacing an old tub with a new one is additionally a moderately difficult task. If the old tub is easily available, the task can relocate immediately; if you need to open a wall surface to eliminate the old tub and position the new tub, the job is a lot harder. In either instance, the job is within a residence handyman's skills, although you will need a helper to move out the old bathtub and also set in the brand-new one. Make certain you have certified yourself for the task as well as are comfortable trying it. As opposed to hiring a contractor to take control of a halfway-completed job, it is far better to think about employing one before you begin. Opportunities are you may require a specialist plumber to make tube links.
This short article will certainly aid you install a new bathtub in your restroom if you have actually already bought a new bathtub and don't need to transform the plan of your previous water supply pipelines.
Your tools and material checklist need to comprise the following:
Preparing for the Installation
First of all, the sustaining framework provided with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the tap features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final setting.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you should do is separate the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The procedure of eliminating the existing taps can be rather bothersome as a result of the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Utilizing the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make certain that the tub is leveled all round. This can be attained by examining the level and also adjusting the feet on the tub until the spirit level reviews level.
To mount faucets, fit all-time low of the outermost adaptable tap adapter to the suitable supply pipe by making a compression sign up with; then do the exact same for the other tap.
Turn on the water as well as inspect all joints as well as new pipework for leakages as well as tighten them if necessary. Fill the bathtub as well as also check the overflow outlet and also the normal electrical outlet for leaks.
Lastly, deal with the bath paneling as described in the producer's user's manual. Tiling as well as sealing around the tub ought to wait up until the tub has actually been utilized a minimum of when as this will settle it into its final setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washing machines are in place between the tap as well as the sink. Secure the faucet in place with the manufacturer provided backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former type needs to be connected to the faucet ends first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a stiff seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to problems with moisture as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes as well as cartridges, and also are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to enable the movement experienced when the bathtub is in usage. The sealer can crack fairly early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is recommended to fit the tiles using waterproof or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about A Step-by-Step Guide to Installing a Bathtub? Try leaving a remark directly below. We will be pleased to listen to your reactions about this write up. We are looking forward to see you back again in the near future. Loved our review? Please share it. Let somebody else discover it. Thank you so much for going through it.
For quick relief, contact! Report this page