Step Tutorial for Installing a Bathtub
Step Tutorial for Installing a Bathtub
Blog Article
Were you trying to find critical info about Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't exactly rocket science, yet it does call for strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately difficult project. If the old bathtub is conveniently obtainable, the job can move rapidly; if you have to open a wall to eliminate the old bathtub and place the brand-new tub, the task is much harder. In either instance, the task is within a house handyman's abilities, although you will need an assistant to leave the old bathtub and also set in the brand-new one. See to it you have actually qualified on your own for the job and also fit attempting it. Instead of employing a professional to take over a halfway-completed project, it is far better to take into consideration utilizing one before you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will aid you install a brand-new tub in your washroom if you have actually already gotten a new tub and also don't require to change the arrangement of your previous supply of water pipelines.
Your devices as well as product checklist should comprise the following:
Getting ready for the Installation
Firstly, the supporting framework supplied with the bath must be fitted (if needed) according to the manufacturer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to see to it that if the tap features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of both taps utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize all of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic due to the limited accessibility that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before carrying on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Using both wood boards under its feet, position the bath tub in the required setting. The wood boards are handy in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level and changing the feet on the tub until the spirit level checks out level.
To install taps, fit all-time low of the furthest versatile tap adapter to the proper supply pipeline by making a compression join; after that do the exact same for the other tap.
Activate the supply of water as well as examine all joints as well as new pipework for leakages and also tighten them if necessary. Fill the bathtub and also examine the overflow electrical outlet and also the typical electrical outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the producer's user's manual. Tiling as well as sealing around the bath tub needs to wait till the bath tub has actually been made use of at the very least once as this will resolve it into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and the sink. Protect the tap in position with the producer provided backnut. Once the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous kind needs to be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall surface between the bath and also the tiling, resulting in difficulties with moisture and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components and installations. They are offered in tubes and also cartridges, and can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to enable the movement experienced when the tub is in use. The sealer can break relatively early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily readily available on the market. It is recommended to fit the tiles making use of waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very serious about How to Install a Bathtub and I really hope you liked the page. Be sure to set aside a second to promote this write-up if you enjoyed reading it. We take joy in reading our article about How to Install a Bathtub.
Quick solution? Call. Report this page